🪚 FREE: 8-part video course on building your first acoustic guitar, from my online course → https://ericschaeferguitars.com/free 🔴 Register for a Hands-On Guitar Building Workshop: https://www.ericschaeferguitars.com/learn-to-build-your-own-guitar/ 🔴 Check out the Online Guitar Building School: https://ericschaeferguitars.com/course-directory/ 🔴 To commission an instrument from Eric: https://www.ericschaeferguitars.com/instruments-ordering/ 🔴 Check out the Radial Rosette Maker Jig: https://www.ericschaeferguitars.com/the-radial-rosette-maker-kit/ 🔴 Donate and Support US Military Special Operators through the Art of Guitar Building: https://www.reveilleguitarproject.org/donate
Audio and video play straight from the show's own hosting. PodSubs stores and serves no media.
Transcript
From the show. Tap a time to play from there.
SPEAKER_00We are doing QA today. So question and answer. Obviously, as always, if you guys have a question, because this is live, you have the opportunity to throw it in the chat. And I will do my best to get to every question in there that isn't just a spammer trying to promote their website or whatever. I'll try and get to everybody. And at the same time, we're also going to jump into the members forum. That's the online course that I sell for guitar making.
SPEAKER_00When you purchase that course, you get access to a private members forum where you can have a dialogue with luthers from all around the world. There's over 500 luthers from around the world, all building guitars, just like you are, sharing their tips and tricks and talking with one another, including myself. And then also you get the benefit of having this fun live stream show where I address a lot of that dialogue and some of the questions that you guys have in the members forum.
SPEAKER_00So if you're interested in that, go to ericshaeferguitars.com and you can sign up for the online course there. So, what kind of questions are we going to be getting into today? I took a brief look at the Discord members forum, and there was a great question on bandsaws and basically how big of a bandsaw, what are my bandsaw requirements for resawing dense tropical hardwoods, the kind of woods that we love to have for acoustic guitars.
SPEAKER_00I have a lot of thoughts and opinions on that. Obviously, I'm a big bandsaw guy. I've got three bandsaws in my shop right now, and I have resawned at all different levels of capability, if that makes sense. I've resunned on much smaller bandsaws, and now I have a very professional, dedicated resaw as well. I'm going to try and cover it from both of those angles, depending on how the person asking the question what the context of their environment is.
SPEAKER_00So I'm going to really try and give them a fully fleshed out answer. And then we have, I think, some questions and calls for gluing the back down, stacking the heel, making a uh three-layered stack for your heel block under the neck blank. I didn't write this down, so I'm going off the top of my head right now. We'll jump into the Discord in just a moment. But first, let me tell you a little bit about what's going on for me here in the shop. I just finished another eight-day workshop with Revelie Guitar Project.
SPEAKER_00Revelie Guitar Project is a 501c3 nonprofit that collects donations to send special operators from the US military, usually guys who are transitioning out of their duties, send them to an eight-day guitar building workshop right here with me in Robasonia, Pennsylvania. This is the, I believe, the fifth class I've done with those guys.
SPEAKER_00Always a blast, always super fun. It's a different group every time. It's not the same group, guys, obviously. And I think I have a picture of them up right now. So yeah, we got Pat, Tim, and Alex. Man, we had just a blast. A lot of jokes. A lot of jokes. And the four dudes building the guitar, you can imagine just the type of humor that we tend to get into here. But I won't get into that. We had fun, it was great. And they built three awesome guitars.
SPEAKER_00There were very few mistakes or touch-ups that had to be done in that class. The execution on those guitars was remarkably good. In fact, probably the most major mistake that was made was my own in prepping some of the materials. I made a little mistake there that we had to work around. But everything worked out. And yeah, another great eight-day class. Also, what I got going on for me right now, let me pull this off the screen here. I actually just achieved my final piece of equipment for the machine room downstairs.
SPEAKER_00So you guys who have been following this for a little bit might be aware that I've been spending an inordinate amount of time on auction websites and even going to some physical in-person auctions trying to invest in a lot of semi-industrial level equipment so that I can be just way more efficient in batching out materials, and especially because I now sell tone woods back and sides and tops and things like that.
SPEAKER_00And so I finally found the last piece of equipment that I wanted to get here. So in the middle of the screen there, we have a drum sander, which I just won at an auction. It is a Supermax 37-2, 37 by 2 drum sander. What that means is it's 37 inches wide, and there are two drums instead of one. So this thing is a friggin' beast. At the same time, I can pass two guitar backs or tops through there side by side because of the extra width.
SPEAKER_00I was actually just looking for a 25-inch, but the larger version showed up on the auction site, and I won the auction for an absolute steal. What did I spend there? Like$1,500, something like that. So it was really good. It is the older version of the Supermax 37x2. So in the past, Supermax was owned by Performax, and they now are under the umbrella of Laguna.
SPEAKER_00And so uh a little bit of an outdated machine, but honestly, just as good as far as I can tell as the modern Laguna-owned Supermax machines, and I've used them in different shops, so I've got a lot of experience with the uh the other more modern machines, and this one functions basically the same. So, anyway, super stoked about that. Oh, I also got in the right hand side of the picture here is uh it's not assembled yet, but a bunch of random pieces for a gigantic cyclone, a dust collection system that I'm going to have to assemble and get all the ductwork set up.
SPEAKER_00So just moved into the shop a little under two years ago. And so it's been a lot of work getting everything up and running. And the final piece of the puzzle will be the ductwork for the cyclone. It's a five horsepower cyclone. It's going to be way overkill for what I have, but as far as I understand, there's no downside to having too much horsepower for your dust collection system. And it's really just all upside, aside from maybe a a little bit of a higher cost to run it, because you're, you know, obviously going to consume a little more electricity running that five horsepower motor.
SPEAKER_00So yeah, that's what's going on here. I'm very excited. I actually haven't been working on guitars at all lately, which is kind of a bummer. I'd like to get started on my next guitar since I finished the guitar 116, the Florentine Cutaway All-Maple Parlor guitar. But I've been just, you know, up to my neck in other projects. That happens all the time. And in a sense, it's actually nice to take a breather from guitar making so that I can think a little bit and gather myself and then be ready and also be just very enthusiastic about the next project when I do start it.
SPEAKER_00Okay. So with that said, we can get right into your questions. But before we do, if you like what I do and you get a little something out of the lessons that I teach, you can go to ericschaeferguitars.com and there you will see a schedule of dates for the hands-on workshops that I do here in Robasonia, Pennsylvania. So we talked a moment ago about Revelie Guitar Project and how they come out for these classes. That's a little bit separate from my actual eight-day workshop, which is something that obviously is open and available to the public.
SPEAKER_00You don't have to be a special operator to take this class. You can just go to ericshaeferguitars.com and register right there. There's only three students in the class. We go very deep on these classes. This is not a kit build. This is a serious guitar building course where you learn the proper fundamentals. And also, while you're there at erickshaverguitars.com, if you don't want to come out here to Pennsylvania to take a class, you can purchase my online course Building an OM Acoustic.
SPEAKER_00There are over 60 full-length instructional videos going deep on every aspect of guitar making from building the jigs all the way out to applying finish. So check that out, erickshaverguitars.com. And lastly, the tonewood shop is now live also at erickshaverguitars.com. So check out some of the tone woods I have there. I have some really interesting spess art oak and some Tasmanian blackwood. I haven't been able to cut up any new woods for a while.
SPEAKER_00That's definitely something that I'm going to be doing in the next couple of weeks or so. I'm going to probably start resawing a little bit more and get some more stuff up on the website for you guys. So check out what's on there now. But also, if you go on there in a couple of weeks, I think you're going to see a lot more. Okay. Oh, and Tom Casty is in the chat. Welcome, Tom. Always great to see you here. And he writes, I did Eric's workshop in 2022. It was awesome. That's right, Tom.
SPEAKER_00That was a good time. All right. So we are going to jump into the members forum. All right. And we'll just go right down the line here. Okay. Our first question here comes from Fish 6743. And he writes, I have reversed the grain direction of the three-inch block in the next stacked blocks. He's talking about the heel block. Is this going to be a problem?
SPEAKER_00Should I cut it off and make new blocks? And just a little context to his question there because I read a little further down. Larry responded and then he responded back. There's a little bit of a dialogue there, but just some context. Let me pull that off the screen. What he's talking about is he when he layered his blocks, he accidentally rotated one of the blocks 90 degrees so that the end grain would be sticking out at the side rather than sticking straight out.
SPEAKER_00And it isn't a problem per se, but I would just redo it because it's going to affect the way that the neck is carved. It's going to make it more difficult to carve because the side grain carves a lot more readily than end grain. End grain is much harder than side grain. And so if you have that alternating both on this face and on the other face, as you're carving, you won't be able to help but dig out odd little gullets in the side grain right next to that really hard end grain.
SPEAKER_00It's not a huge waste. I would just throw out that block and make a new one. And actually, reading further down in the dialogue there, that's exactly what fish did. Okay, we're just going to call you fish. How's that? And yeah, but that would that's the only problem. The only other thing I would maybe add to that that I can think of is if it's a Balton Mortise Antenon, if you're going to be drilling a hole and then inserting that brass insert into half into end grain and half into side grain, I think that would be a little bit of a problem.
SPEAKER_00I know that when I drill holes for brass inserts into end grain, the hole size is actually for me slightly different than if I were drilling one into soft side grain. So again, that's just something to think about, not necessarily a huge problem. Like I said, I would just redo it. Why not? Not to mention it'll it'll look a little cleaner, right? If you don't have that alternating grain, unless that was a some sort of visual effect you were going for.
SPEAKER_00Next comment I wanted to bring up here, I think was this one here from Patrick. And he writes, I'm going to upgrade the tuners on my Martin 000018. If you haven't tried these, you should. It's a unique look and they're well made. Martin made a few of these guitars with banjo tuners. And so I've got a picture right here. This is what he's talking about. So I just wanted to bring this up here because I built one guitar with banjo tuners once as an experiment, and that guitar turned out horrible, really horrible in a number of ways.
SPEAKER_00I won't even show you the guitar. Perhaps you guys have seen it. It's in some of my videos, I think. But just aesthetically, I did a lot of weird things to that guitar, and it was too much. It was obscene looking, in my opinion. Also, I was experimenting with some things about string tension, and it turned out to be a fail. But anyway, I won't get into all of that. But the banjo tuners I used were I think four to one, which is a typical banjo tuner ratio.
SPEAKER_00You guys out there on the internet can correct me if I'm wrong. Let's see. Actually, I'm gonna correct myself. Four to one banjo tuners. Are they common? Okay, the AI is spooling up. Yeah, they're the standard. Okay. Yeah, so four to one is the standard ratio. These I was interested to see that Patrick has up here. These are 10 to 1, because he's got another picture here. Here's the box. High ratio banjo tuning pegs by Ricard Cyclone.
SPEAKER_00And it says precision 10 to 1. Now, 10 to 1, I think it you can absolutely use for a guitar. And I guess that's what these are designed for, because typical guitar tuning ratios are hovering around 14 to 1 or 16 to 1. So 10 to 1 is just a little bit less than that, and it I think will work a hell of a lot better than the experiment I did with my four to one tuners. The problem with extraordinarily low ratio tuners is especially on the steel string guitar, it's just so difficult to find your pitch, right?
SPEAKER_00You can detune and retune the guitar in theory a lot quicker, but you'll actually spend way more time just overshooting your pitch than undershooting it and just trying to like settle on a precise note. That's why you want that ratio to be pretty high. For regular geared tuners, I like to aim for an 18 to 1 tuning ratio, which Goto 510 minis have. So I'm pretty happy with those. And then I also, as you guys know who watch these videos, I also use Steinberger gearless tuners a lot.
SPEAKER_00And those have the equivalent of a 40 to 1 tuning ratio. A little bit overkill there with the 40 to one, but if you really value that precision, that's definitely another way you can go with it. Okay, let's go into shared mistakes here. Although I don't know, Carl, that this one's a mistake. So Carl Mill writes, I use individual segments about 1.5 inches long. He's talking about for the calls that he uses. Here, I'll pull up this picture.
SPEAKER_00The calls that he uses to create the ring around his back or his top when he's gluing it in the go bar deck. Okay, so if you're gluing up your top or your back in the go bar deck, you want some sort of call to evenly distribute out the pressure from the go bar so you don't get little flares coming up along either side of the go bar where the wood doesn't really seal well. Calls solve that problem. Not to mention they protect the surface from dings and such.
SPEAKER_00So I actually like he's got those little holes drilled in the calls so that the go bar has a place to sit in them. I think that's a smart idea. And then also I just wanted to comment on this saying that I actually used to do the same thing with just using little pieces because I didn't want to build four different rings for different sizes of guitars. Sometimes there's no real right or wrong answer here, but sometimes the answer is to have an adaptable solution that you can just use for several of your models, right?
SPEAKER_00And other times it makes sense to build an individual separate template or jig for each exact model. But I think this is uh this is the way I would do it. I'll put it that way. If I was uh still gluing up these in the GoBar deck today, I'd just glue them up in a different manner, which I won't get into. But yeah, that looks great to me. Keep it up, Carl. Keep it up. Okay. Oh, and Carl also just ordered a radio rosette maker from me, so I'll be shipping that out soon, along with a couple other of you guys out there.
SPEAKER_00Keep checking your email for the tracking number, and I'll get that out to you. And uh, let's get some questions in the chat too, guys. Actually, I haven't looked at the chat here. Hey, good to see a new live stream. Yes, looking forward to the rosette, Jake. Great. Trying to navigate back to there. We go. All right. Next question comes from Talmir. Talmir writes, Hi everyone, I'm considering purchasing either the Record Power BS350S or the Rikon 10324 from my guitar workshop.
SPEAKER_00These are bandsaws, by the way. Let me pull this up onto the screen. So, yeah, there's the Rikon. Sort of a classic, well-known bandsaw. The record, I actually don't know this company at all, and I feel like I know bandsaws pretty good. He's from Israel, so this could just be an overseas company that I'm not familiar with at all because it's not from here. But yeah, we're gonna take a look at this a little bit and maybe I'll even look at some of the specs on these and we can talk about it.
SPEAKER_00But also, I just want to speak generally about the requirements for resawing, particularly in the context of guitar making. He writes, these are basically the only two options currently available in stock here in Israel, as our selection of band saws is pretty limited. My main priority is the ability to reliably resaw hardwoods into acoustic guitar backs and sides, including dense woods like rosewood and granadillo. Does anyone have experience with either machine, particularly for resawing?
SPEAKER_00I'd appreciate any recommendations regarding power, cutting capacity, accuracy, and overall performance. This is a great question, Talmir. And a couple things I want to highlight there that you mentioned is that your main priority is the ability to reliably resaw hardwoods specifically. And so there's a lot of information out there that I think will steer people in the wrong direction. If you're not very clear on exactly how involved with resawing you're planning on getting, if you just get on the Google and look this up, you'll find that the opinions on the internet will push you towards a pretty low-powered bandsaw, and sometimes even with what I would consider a very small blade, because to get away with resawing, meaning to kind of barely be able to do it, you'll be able to make the cut, but you'll kind of take your bandsaw blade if you keep using it, and each cut will take you an order of magnitude longer than if you had the appropriate tool.
SPEAKER_00Okay. And so that sort of minimal situation that most people are in would be like a 14-inch bandsaw with a probably a one and a half horsepower uh motor. Okay. But with the guitar parts, we're trying to cut extremely tall resaws. Especially if we're doing back and sides and you're gonna use your dense tropical hardwoods, you're cutting about seven inches height of rosewood.
SPEAKER_00Having a half inch blade, even if it's a really good quote unquote resawing blade, like the wood slicer, which I like that blade, but it's only a half inch. The problem sometimes with the term resawing is if you're not building guitars and the General woodworking community, they generally have a different conception of resawing. And what I mean by that is generally when they're talking about resawing, they're talking about making veneers out of material that might be four inches tall.
SPEAKER_00We're talking about quite a bit taller. And the taller you get, it just gets exponentially more difficult. There is a general rule out there which says that you need one horsepower for every four inches of resaw heights. Again, you can skate by with lower, uh a lesser setup. I did that for years, but I wasn't doing it a lot. And whenever I did make a resaw cut, I would have to really set up my bandsaw for it to really dial in the drift as much as I could.
SPEAKER_00And then often I would be using a resaw bar because I'd have to adjust for the drift as I was going. The reason for that is on a smaller machine that can only hold, say, up to a three-quarter inch blade, through that much wood, it can't help. It doesn't have the beam strength. It can't help but deflect slightly here or there, even if your feed rate is really slow. And so you end up having to use a resaw bar to adjust the drift as you go. It works, but again, it's not ideal. The ideal thing is to just get a machine that has the capacity for a much wider blade.
SPEAKER_00The width of the blade, I cannot stress enough, along with the horsepower. Those are the two most important things. Everything else is nice to have, but the requirements are a horsepower that makes sense with what you're cutting, and a width of blade that makes sense with what you're cutting. The reason the width of the blade is so important is because the wider the blade, the more beam strength that blade has. And it's that beam strength that prevents it from twisting and deflecting from side to side, which causes all of your bandsaw drift.
SPEAKER_00If you're having nightmares about bandsaw drift right now, I'm telling you, when you upgrade to a bigger machine that just has the capacity for a wider blade, that all goes away overnight. Obviously, I don't know what your budget is here, and I didn't really let's take a look at these two machines because that probably gives you a good idea of what your roughly what your budget is. Because yeah, this is a 14-inch machine. If I had to guess, it's probably a little over a thousand bucks. There's the record power, which I don't know anything about.
SPEAKER_00So let's look up that RICON 14. 14 inch 10-324 TG. Okay. Yeah, that's it right there. All right, and I don't see a price because it says currently unavailable, but I can see a lot of similar price things. So yeah, there's another RICON that's similar here. That's a 1600. Okay, so the 14 inches, uh, that that's your resaw capacity. That is great. That doesn't bother me one bit.
SPEAKER_00And do they give you the horse? I don't see the horsepower on here. I'm on Amazon though. Anyway, I'll just give you some general guidelines. So, again, that one horsepower for every four inches rule is pretty important. I have a 20-inch band saw, which is over the top. I got it at an auction. So one thing I've noticed is when you get your equipment at these auctions. Hold on, let me pull that off the screen. When you get your equipment at these auctions, every piece of equipment that I got, and I got like five different pieces of equipment, I ended up getting more than what I was trying to attain, and obviously for less money.
SPEAKER_00That's my first tip is instead of buying new, maybe to just look up. I don't know what's going on in Israel, but maybe I don't know, maybe there's some industrial auctions from old companies that went bust. I don't know. Look it up. There might be some auction site over there that'll work for you, or just generally on the mainland of Europe. That you could, I don't know, have it shipped in or something. Yeah, auction sites here in America. I use IRSAUCHINE.com, not IRSAUction.gov, which is actually the IRS, the Internal Revenue Service.
SPEAKER_00IRSAUCHING.com is, I think, intentionally doing a little play on words thing with their acronym. I don't know, trying to get you to associate the IRS with the auction that service that they're providing. But IRS actually stands for not internal revenue service, but for industrial recovery service. So that's IRSAUction.com. Great site. They're actually headquartered here in York, Pennsylvania, which is not too far from me.
SPEAKER_00Maybe about an hour drive. And so you can get some real steals there, and you can end up getting a higher capacity bandsaw for less money if you're willing to be a little bit patient. And and you're not, you know, brand loyalty to a specific thing. You look for a couple different models that you like. Maybe it's Powermatic and Laguna, those are two that I those are my two favorite personally. The Raycon's fine, but I do like, especially for Bandsaw's Powermatic and Laguna a lot.
SPEAKER_00And so if you're just willing to be patient and peruse those sites, keep a tab, a bookmark on your computer, you can constantly go in and check. You can do really, really well that way. What you're looking for to get into resawing hardwoods. Now, I'm assuming, just because by the way that you said it, that you're not just trying to resaw a couple sets one time and then swap out the blade for a smaller blade to do other tasks.
SPEAKER_00Okay. I'm assuming, I think maybe incorrectly, that you are looking into getting into a dedicated resaw, in which case I would say you're going to want at least two horsepower, would be a bare minimum. It's probably still too low. You probably want at least three horsepower. My machine's five horsepower, but that's because it's a 20-inch resaw capacity. Although I never need the full 20 inches again, because I'm just doing guitar parts, guitar backs and sides.
SPEAKER_00And so 20 inches is actually a pretty massive overkill. And so is five horsepower. But it's better than undershooting it and having your machine literally just not be able to keep up with the task without causing massive drift and burning out the blades, breaking the blades, overstressing the wheel hubs and everything. You want to do this right if you're thinking about really getting into it. Now, if you are just trying to set yourself up to once every two years cut five sets, take off the generic blade on there, put on your larger resaw blade, make those cuts, and then switch it back, which a lot of people do.
SPEAKER_00That's fine. Then a 14-inch bandsaw with a 1.5 horsepower motor will just barely squeak you by. Okay. And let's see, we got a lot of comments here in the chat. Tom Casty writes, I have a jet 14-inch bandsaw in my shop and have considered getting the riser blocks to enable resawing up to 12 inches. It's not high on my priority list, but what do you think about that? Yes, I'm glad you brought that up, Tom, because I was going to mention riser blocks. And mostly I was going to mention them not to say don't do it.
SPEAKER_00Again, if you're just trying to just barely squeak by like cutting one thing once a year or something like that on their bandsaw, and then you switch back to using your bandsaw to cut curves and things like that. The riser block will get you there, but it's really not the right way of doing it because what you're doing is you're raising the resaw capacity without changing any of the fundamentals about the bandsaw. It still has probably a one and a half horsepower motor and only the capacity to fit a, I don't know on your bandsaw what it is, but I'm just going to guess a half inch or three quarter inch blade.
SPEAKER_00And so without changing that and just increasing the resaw capacity with a riser block, I think you're just going to be disappointed in the performance of it. But again, if you don't mind that and you don't mind spending two hours to make one cut, you think I'm joking, but sometimes it depends on the wood that you're using. I'm probably exaggerating a little bit, but it can definitely be like an hour just to cut one or two things.
SPEAKER_00It can be a really big deal. And then also the surface is extremely not smooth and probably a little blackened from just the friction generated. So yeah, that's my opinion on the riser block thing. But again, if that's the only thing you can do, it'll get you across the finish line. You don't have either this, you're not gonna, you're not planning on upgrading your whole bandsaw. But that's just the honest truth about it. I'm giving you guys a lot of hard truths, I think, here about resawing.
SPEAKER_00Because I think a lot of people will try to sell you on the lower end 14-inch band saws and getting riser blocks and stuff like that. But again, if you're trying to be serious about it and you're a guitar maker who uses hard tropical woods, it's a serious undertaking to be equipped to make those cuts. And it's just gonna cost a little bit of money, to be honest. And so I'm actually trying to honestly save you money, if that's what any of you are trying to do, so that you don't waste your time getting a 14-inch bandsaw with a riser block, and then eventually years down the road, because you just get sick of standing there like this, moving a millimeter a minute for hours on end.
SPEAKER_00That was my experience. I went through that for a long time until I was eventually like, screw this. I am getting a serious bandsaw. So, anyway, that's the person I'm talking to right now, okay? Whoever's in that situation. All right, Tom Casty writes the motor is one horsepower and I can use up to a three-quarter inch blade. Okay, yeah, yeah. So that's again, I've been there, I've done it. It is doable. And he does say I would only be reselling occasionally, so that is doable.
SPEAKER_00Yeah. What do you got to lose? Try it out. Uh, you just won't be doing it a lot. And it sounds like that's what you're planning on anyway. So that's great. There's a newer one that is the 1014-14 and has a one and three-quarter horsepower motor. That's quite a bit better. That would definitely help. One and three-quarter again. I feel like crossing that two horsepower threshold is bare minimum for me.
SPEAKER_00So I still feel like one and three-quarters, although that's close, is a little under just a tad for guitars. Okay, let's see. Should I jump into YouTube and look at some of those questions? I don't know. Let's check it out. While I'm doing that, throw some more questions in the live chat, please. Okay. My painting writes I have a classical crossover that has a great sound, but the D string always gave me trouble.
SPEAKER_00When it was in tune at the open position, the second fret E was always frustratingly sharp. So I compensated a saddle by pushing the D back like you have the B, and it solved it. Darn tempered scales. Love to hate them. Yeah. If you've ever looked into what a true temperament fretboard looks like, I think it's fairly interesting to do that. In fact, I'll pull one up right now. True temperament fretboard.
SPEAKER_00And there's always a good image up here that I like to pull up. Yeah, this is a good one. All right, look at these crazy squiggly frets that look like they were drawn by one of my kids who are four and five years old. Actually, no, they're too old for this. They would draw a much straighter line than that. What am I talking about? But it looks like it was drawn by a one-year-old. So this is interesting because a true temperament fretboard is something that was invented by someone in Sweden, I believe.
SPEAKER_00And they have the patent on this, and they actually can sell you these little squiggly frets and fretboards that are slotted for these squiggly frets. And the idea is very simple. What you're looking at is the actual true positions where at every single fret location, every note will intonate accurately. And so it's interesting to look at that just to recognize how far off some of these will sound.
SPEAKER_00And intonating at the saddle, which you just talked about, intonating at the saddle isn't really going to correct this. It's just going to move the problem somewhere else. So you were talking about, I think, that the second fret on the D string. And so when you're looking at an intonation issue in a very specific spot and not everywhere else, your intonation corrections at the saddle at best are going to distribute out that discrepancy a little more evenly across the other positions, but it's not going to eliminate it.
SPEAKER_00So you might have just moved the problem somewhere else. Or if done correctly, you more evenly distributed it so that it's not noticeable anywhere. Yeah, I always just like to bring this up as an interesting visual, especially for some people who are super have really good ears, right? And get actually get bothered by the slight out-of-tuneness, the natural out-of-tuness of a guitar. Looking at this picture, you can realize that having some perfectly in-tune instrument is just simply not possible.
SPEAKER_00Again, unless you build a true temperament guitar. Now, true temperament guitar is not for everybody. If you like to bend the strings at all, you're not going to like a true temperament guitar. Okay. Your bends are going to be wildly out of tune and inaccurate. As far as I've seen, these guitars are very rare and they're really just for metal shredding. And that's it. Okay. We got a question. Hold on, let me get this off the screen so we can stop staring at those disorienting frets.
SPEAKER_00And Tim on Pim Montag 21. Tim Montag 21. I have a question about the fretboard extension bracing. Which is better, or what are the advantages between popsicle stick style bracing and a fretboard extension attached to the neck block. I think I know what you're asking. You're saying having the A-frame braces that go up under the fretboard extension, or having the L-shaped neck block.
SPEAKER_00So everything north of the transverse bar is essentially is designed to be, if it's designed right, is designed to be essentially acoustically inert. It's designed to be over braced just for the purpose of housing the neck joint and supporting the fretboard tongue, which always wants to torque and dive into the soundboard. So whenever I look at all the bracing that's above the transverse bar, for me it's just the fretboard graft and the neck block itself.
SPEAKER_00So I would just go with whatever supports the fretboard extension. So the fretboard extension is supported by the transverse bar. And if you have extra A-style braces that go through the transverse bar, I think that's what you're talking about. The popsicle stick braces that start at the X brace travel through the transverse bar and then go up towards the neck block. That's gonna add extra security, I guess, to the situation.
SPEAKER_00But it's not necessary. My popsicle stick sound hole braces just end at the transverse bar, and then above the transverse bar is simply a fretboard graft, which the fretboard graft is not for structure. It's just a graft, it's not a brace. That's just to prevent splits from the unequal shrinkage you get from the two woods that are glued to each other. The ebony of the fretboard, let's say, and the spruce of the top are going to shrink at vastly different rates. And because they're glued to each other, it's a very common problem on old guitars to get splits right along the edge of the ebony fretboard, those splits going into the soft wood of the spruce.
SPEAKER_00Because again, that that fretboard is going to shrink differently and it's going to want to just pull that spruce with it, which is what causes those cracks. Yeah, he is talking about L-shaped neck block. Yeah, I was just trying to think of the term for it. But okay, he's saying the L-shaped neck block versus the fretboard graft. You just need the fretboard graft. I don't know what someone who installs the L-shaped neck block exactly what they would say, but I guess it's just extra security in that area, beefing it up even more.
SPEAKER_00I don't know. To me, I don't do it. So by definition, I don't think it's necessary. Carl Mills writes, back to the bandsaws again. He writes, also, you can look for previous year models. I got a 20% discount on four models. That's a great idea. Yeah, absolutely. Yeah. In fact, almost everything I got at the auction is a not everything, about half the things I got are older models that they don't make anymore. Part of the reason why I got such a great deal on them.
SPEAKER_00Okay. And if you like what I do and you get a little something out of this, you guys know what to do. Go to Eric Schaefer Guitars and you can check out the schedule of dates, as I mentioned in the beginning for my eight-day workshops. Oh, and by the way, the schedule's not up there right now. So I said that earlier, but I'm making the schedule for 2027 right now. There is one date in November that's up there if you want to sign up for that. But I assume most people are looking out into next year. And I got to get that out there. So there is an opportunity for you guys. If you are interested in signing up for one of these workshops, because I'm still making the schedule for next year, if you message me, email, or you can even give me a phone call.
SPEAKER_00You can find my contact information on my website. You can pitch some dates to me. And if it doesn't conflict with anything else for me, I'd be happy to make that work for you. Okay. So with that said, thank you for tuning in. I'll see you guys in the next one. Bye for now.
🪚 FREE: 8-part video course on building your first acoustic guitar, from my online course → https://ericschaeferguitars.com/free 🔴 Register for a Hands-On Guitar Building Workshop:...
🪚 FREE: 8-part video course on building your first acoustic guitar, from my online course → https://ericschaeferguitars.com/free 🔴 Register for a Hands-On Guitar Building Workshop:...
🪚 FREE: 8-part video course on building your first acoustic guitar, from my online course → https://ericschaeferguitars.com/free 🔴 Register for a Hands-On Guitar Building Workshop:...
🪚 FREE: 8-part video course on building your first acoustic guitar, from my online course → https://ericschaeferguitars.com/free 🔴 Register for a Hands-On Guitar Building Workshop:...
🪚 FREE: 8-part video course on building your first acoustic guitar, from my online course → https://ericschaeferguitars.com/free 🔴 Register for a Hands-On Guitar Building Workshop:...